Відео

How did you add those dimensions into the plank at 2:09?

Hi Macon, I love your series of videos on your restoration. Extremely helpful to me. I am starting my own journey on restoring my own organ that I have had stored since I was a ten year old girl. 50 years later I now have the space and time to attempt it. I noticed you have some borer holes in the wood surrounding the bellows, have you treated this insect with anything? I have quite an infestation. Many thanks Leonie

I had a similar experience with my machine. I purchased from a different Chinese company with similar customer service. The language barrier was there, but they really do try. I found a set of 12 ton machine moving dollies from Vevor available from Amazon and are they ever solid. The crate they came in was impressive enough, and the wheels only cost me $250 Canadian dollars. It made moving the machine around the shop so easy. My machine arrived in a crate that was damaged, but the machine itself was fine. You had a lot less assembly to do. My machine arrived with the gantry not attached and laying strapped down on its side. This is the third machine I've purchased from LintCNC and the first needing the gantry installed. It's not a huge issue, but surprising. I needed to use an engine hoist to flip it upright and positioned on the rails. They said they do this so that the rails are not damaged in shipping, so anyone who is planning on purchasing a machine should ask the seller if they will need to install the gantry. Other than you having a Blue Elephant with DSP controller and mine a LintCNC Mach3 machine, they pretty much seem to be the same machine.

Thanks for your video Do you have any video how to Make vecar work cnc .thanks

I wanna build a legendary jump rope set.. so watching this video was super informative!

how much did you pay for the cnc?

Great job! For the sound, it might be the leather belt covering the 7 holes of the pump. Instead of leather from both sides that belt if made in double layers the upper layer is leather and the base layer facing the 7 pump holes is made of soft silicone.

Great improvement, you are learning fast! However, install a riving knife for increased safety. ✌

This is so helpful. I am in the process of starting to restore a 1890s reed organ myself. I'm reading in the forum and watching videos. This is the most helpful series. What chemical did you use to clean the stop rods? Just wondering.

You nailed it man. It turned out that your plan was not so doggy afterall. 🤘

Lekker ou bul.

simple idea and it seems easy for me to make it myself at home I happen to be looking for a tutorial to make something like that... I have watched many videos but they are complicated... while this is simpler... thanks for sharing

Do they come with a vacuum suction option instead of clamping?

What is the diameter and kilowatts of that spindle?

Simple❤

Excellent video and beautiful end product. Special kudos for being a great dad and teaching your kids the importance of hard work.

WOW

Wow...this was more than a restoration. I really hope that the materials you chose will stand the test of time and I would like to know how are they performing during the last three or four years since you published this video. Very well done sir. Really impressive.

Wow.. (thats not a good wow) what a way to discourage newbies..!! Copper caps, dowel rods, couple 16d nails and a little bit of lead.. all less than $20 and you can make a nice set and off to knapping you go..!!

How many times I’ve said exactly as you, “I’m way over my head!” Still, we trudge forward. You finished with a good job by the way!

awesome skills attention to detail high standards - deep respect

Dude, you’re a Sal Vulcano look alike.

GREAT MAN I JUST GOT MY BLUE ELEPHANT.... 1 month I just managed to run it good. Feel free to conctact me to share experiences. I am about to machine aluminum.

Simple is best, always! 😊

Why not use fusion 360 for cam? I use it for my 6040 router.

Rope is good but i already built this rope and its not sustainable rope/wire is going to break when you start using it

promo sm

Hi MaconSTUFF, I want to setup my blue elephant with the mozaik software. They're requesting the gcode for the machine.

Lagunas are just rebranded Chinese CNC machines.

Did you do any knapping with those tools yet?

Hi again In the box that you received with the CNC ( and you use it for water pump) you have more clamps, bits and couple of sensors. Are spare sensors or must be fixed somewhere on the CNC as I have exactly the same blue elephant CNC as you

what application do you use to create g code? and how to make g code leaving the cut at the bottom still connected to the cut object

You should be using hot hide glue, it's traditional and it means the work is reversible as the bellows will eventually leak and need replacing again in years to come. I've been restoring organs and harmoniums for 10+ years and would never use anything else.

Hi mate, how did you sort it out the problem with the power cable for dust collector?

Hi mate, you’re doing a great job with these videos for us, thanks As I could see in first video, you’re not using Artcam but Vcarv ? How is it working?

Great job

I like your design. Do you have files for this?

👏👌🇳🇴🤠

All that matters is you are happy with it. One thing I would have done is get the ATC, your life would be much easier.

The machine have a stepper motor?

I own cross rope and many others but this was so great to see made ! Hope you enjoy it

Well met man..! Inspiring

this job is insane i really liked it

Great work mate best regads from venezuela, very good all the explain ang guide thank you

Looks good. I think you would need to check the fence is square after every adjustment.

Thanks for this tutorial

Hi Macon, I am waiting for my own CNC machine(Blue Elephant). i will be using Vectric Aspire. Do i need to contact blue elephant for a post-processor to run the vectric software?

So many videos that you see on UA-cam and you don't know how to place a ground wire to avoid static energy in any electronic equipment! That is very important.

good job MaconSTUFF. @samadabdul1242, do you have Blue Elephant ELEC1325?

I’m impressed.